All Industrial Services Inc. of New Jersey| 190 Boundary Rd, Marlboro, NJ 07746
quote@rbaker.com| 732-222-3553|            
 
All Industrial Services Inc. of New Jersey| 190 Boundary Rd, Marlboro, NJ 07746
quote@rbaker.com| 732-222-3553|            
190 Boundary Rd, Marlboro, NJ 07746 732-222-3553
asset recovery, rigging team with sling and interior demolition

Rigging Safety Guidelines

Rigging Safety Guidelines - Industrial Services

Safety is paramount at R. Baker & Son, which is why we strictly observe all rigging safety regulations, guidelines and procedures on every lift we do. 

Guidelines for rigging safety:

Inspect the condition of your equipment on a daily basis.  Check cables for kinks or worn or broken wires, and slings and straps for fraying or cuts.  Hooks, shackles, and pins should not be bent, and metal should not show corrosion, cracks, or excessive wear.  Any equipment showing damage, no matter how slight, must be immediately removed from service.  

*Know your equipment, and use it properly: equipment and accessories should be selected based on precise load size and weight analyses and calculations.  There is no room for error in rigging; if a load doesn’t meet the safe capacity, don’t make the lift.  

*Develop an approved pick plan where required and whenever possible.  Determine whether a tagline is necessary, especially where clearances are limited.  

*Check slings and connections: Before lifting, remove slack from slings and watch for sharp or jagged edges that may damage the sling.  Ensure that connection points are tight and secure.  

*Position cranes on stable ground and make sure the area is sufficient to accommodate the crane outriggers, and the load.  

*Take precautions when there are high winds, and be prepared for sudden gusts.  If winds exceed or threaten to exceed safe limits, do not make the lift.

*Designate team leaders and signal persons, and assign specific roles to team members taking part in the lift. 

*Crane operators should first lift a load a few inches to make sure it is properly balanced and secured and the equipment is functioning properly.  

*Loads should be moved smoothly over the planned route, with no sudden movements. When necessary, riggers use taglines to control a load and prevent spinning from a safe distance.  

R. Baker & Son’s expert team includes master riggers, professional engineers, and skilled rigging tradesman capable of handling even the most challenging and complex rigging projects. We provide clients with a full selection of rigging services including rigging of heavy equipment and machinery, sensitive pharmaceutical and manufacturing equipment, rigging and dismantling of equipment and process lines, equipment salvage and removal, match marking, reinstallation, and millwrighting. 

About R. Baker & Son All Industrial Services

R. Baker & Son All Industrial Services, a  Service-Disabled Veteran-Owned Business (SDVOB)  in business since 1935, is a premier specialized contractor operating in the United States, Canada and Puerto Rico, with over one hundred employees and an exemplary safety record (we have been directly involved in four sites that received VPP OSHA Safety Awards). R. Baker & Son is financially strong, with bonding capabilities over $10 million. Capabilities include industrial and commercial demolition, rigging, machinery- and plant-moving, dismantling, decommissioning, plant and equipment relocation, interior demolition, selective demolition, warehousing, wrecking and razing, millwright, plant reconfigurations, heavy rigging, salvage, environmental services, remediation, decontamination, abatement, and investment and asset recovery.

R. Baker & Son - All Industrial Services
190 Boundary Road
Marlboro, NJ 07746
732-222-3553

http://rbaker.com/

Full News Archive

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

Recent News

Interior Demo - Making Way For New Manufacturing Facility
Interior Demo - Making Way For New Manufacturing Facility

R. Baker & Son was recently contracted to provide interior demolition services for a new client that had just purchased a 95,000 square-foot rubber tire tread factory. With plans to construct a...
Zero Punch List - Demolition
Zero Punch List - Demolition

Unless its performed by a highly experienced and professional contractor like R. Baker & Son, demolition can be a messy, chaotic process. Demolition experience dictates the best tools, equipment,...
Process Tank Repair Project, R. Baker & Son
R. Baker & Son Process Tank Repair Project

A longtime R. Baker & Son client with several large process tank farms at their New Jersey facility contacted us for assistance with tank repairs. A manufacturer supplying tank agitators needed...
Provides a Wide Range of Environmental Services, R. Baker & Son
R. Baker & Son Provides a Wide Range of Environmental Services

Included among R. Baker & Son’s core services are environmental remediation and decontamination. We boast a team of highly-trained environmental remediation personnel as well as an arsenal...
selective demolition in hospitals
Requirements of Selective Demolition in Healthcare Facilities

Some of the most challenging selective demolition jobs are renovation projects that take place in healthcare facilities, where demolition team members must be specially trained to work in sensitive...
 Plant Demolition and Demolition Contractor Services
R. Baker & Son Demo Team Completes Partial Plant Demolition

R. Baker & Son recently completed a demolition and decommissioning project at a northern New Jersey plant. The first of R. Baker & Son’s tasks was to demolish a 60’ x 30’...
Rigging and Anchoring Heavy Machinery and Equipment
Rigging and Anchoring Heavy Machinery and Equipment

An important work scope that is often overlooked on construction projects is the rigging and anchoring of equipment to concrete, steel platforms, curbs, decking, etc. Anchoring should not be an...
Completes Selective Demolition Project on Christmas Eve
Baker Completes Selective Demolition Project on Christmas Eve

Over the recent winter holiday season, R. Baker & Son was tasked with performing selective demolition at a medical manufacturing facility that produced orthopedic titanium parts and hardware....