All Industrial Services Inc. of New Jersey| 190 Boundary Rd, Marlboro, NJ 07746
quote@rbaker.com| 732-222-3553|            
 
All Industrial Services Inc. of New Jersey| 190 Boundary Rd, Marlboro, NJ 07746
quote@rbaker.com| 732-222-3553|            
190 Boundary Rd, Marlboro, NJ 07746 732-222-3553
asset recovery, rigging team with sling and interior demolition

Excavation of Contaminated Soil

Excavation of Contaminated Soil

Many R. Baker & Son demolition, environmental services, and brownfield site projects require excavation and disposal of contaminated soil and debris.  Before a project can begin, areas of possible contamination must be identified through research of site activities and communication with the client, and soil must be tested for contaminants. 

Soil that is found to contain pollutants must be segregated from clean soil, and both must be disposed of properly.  Contaminated soil must be transported to a treatment facility or to a landfill equipped to handle polluted soil and other materials.  At times, contaminated soil may be treated onsite using a mobile treatment facility. 

Excavated soil may be placed directly into a dump truck for transport to a landfill or treatment facility, or, if it is to be decontaminated or disposed of onsite, it may be stockpiled on tarps or in containers, then covered to prevent it from blowing or washing away.  Workers must follow safety procedures to avoid contact with toxins, and prevent the spread of contamination offsite.  Truckloads of soil should be properly covered and trucks undercarriages and tires may require cleaning before leaving the excavation site to avoid contaminating local roadways. 

R. Baker & Son personal are expertly trained and fully equipped to perform a broad range of environmental remediation and decontamination, including the excavation of contaminated soil.

R. Baker & Son
1 Globe Court
Red Bank, NJ 07701
Phone: 732-222-3553
Web: http://www.rbaker.com

Full News Archive

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

Recent News

Rigging Process Equipment Narrow Shaft
Rigging Process Equipment Narrow Shaft

An old R&D facility in Northern New Jersey needed to renovate an area to make way for an important new expansion. Because real estate for needed process equipment was limited, the only area...
Demolition Equipment Maintenance
Demolition Equipment Maintenance SOP

Demolition equipment is always being put to the test. Every quality demolition contractor looks to get quality name equipment at a fair price. Demolition equipment maintenance falls under two...
Module Rigging & Installation
Module Rigging & Installation

R. Baker & Son recently completed a module installation at a northern New Jersey chemical pilot plant. Working closely with the owner and the module fabricator, the Baker team developed a lift...
Challenging Duct Demolition
Challenging Duct Demolition

A rare malfunction in a large HVAC system caused exhaust ductwork to collapse due to a severe negative pressure condition, and building owners were faced with a dilemma. The 160-ft. duct had to be...
Construction Crane NYC
Counting Cranes to Forecast Construction Growth

Cranes are a familiar sight in New York City and other urban areas, and people who depend on the construction industry for our livelihoods, like those of us at R. Baker & Son, tend to be...
Demolition Contractor in NJ
Demo Protection

Some interior or select demolition projects are complete guts or tear outs where everything must go. Some items need to be identified as not to demolish and remove; this can be done with marking with...
R. Baker Plant Relocation Photo
Plant Relocation Specialists

Relocating a plant can be a complex undertaking, one that requires close coordination, meticulous planning, and good communication among contractors, owners, designers, and facility personnel. A...
Baker Works w/ MEP Engineers to Accelerate Plant Relocation
Baker Works w/ MEP Engineers to Accelerate Plant Relocation

Relocating a plant, whether moving across town or across the country, usually means there will be a lapse in production. The longer process is down, the higher the cost, which is why bringing the new...